Sous-Vide 1.1

October 12, 2014
Leave a Comment

Small update.

Testing showed that the PID tuning was quite finicky. Even with the Auto tuning feature I had enabled, I was having issues with overshoot on the ramp up cycle. I also found that the PID control, by it’s very nature, caused the relay to chatter a lot when the crockpot temperature is near the set point temperature. I attempted to re-tune the PID several times but did not come up with a parameter set that I found to be acceptable.

A step back in controls:

I had previously, in a different project, used a more simple temperature control system. That system simply turned a heater on when the current temperature is low, off when the current temperature is high. It was a very simple method and worked well for a test chamber that was used in testing scenarios that required temperature stabilization over a 30 minute period prior to test execution. With a little bit of modification, the same concept has worked for the Sous-vide too. I added a little bit of logic to help prevent over-shoot. The relay no longer chatters, and the crockpot comes up to and maintains the setpoint temperature.

A step forward in progress:

Now that I have the temperature control segment of the program working well for this application, I can proceed to the next phase. With this new approach to the control, I have been able to remove the PID code. That freed up a large portion of the program memory that I plan on using for other features of the controller. Having free space in the program memory means I can add the profiles, delay timers, a selection of notification sounds, and logging. I’ve already started cooking with the unit, but I can’t wait to get the next set of features added to the program.


Posted in Arduino, Controls

Making a custom sous-vide controller phase 1

September 15, 2014
Leave a Comment

What the heck is sous-vide?

Sous-vide is a method of cooking using a water bath at a highly controlled temperature. I became aware of the method in the same way most people do, the Modernist Cuisine.


The market has dedicated sous-vide cookers, or controllers that will convert a rice cooker or slower cooker into a sous-vide cooker by adding a temperature sensor and regulating the heating element.


Controllers can be bought with similar functions of what my basic controller can do, but I have plans for expansion. There are kits to make your own controller. But if you are like me, you might have most of the parts already on the shelf. And you would rather do a little work from scratch. My inspiration for this project came from an article I read in Make magazine for the Yogurt bot. My wife becomes a little nervous when a new Make magazine shows up in the mailbox.



  1. I wanted to create my own controller from parts I had on hand, and buy as few parts as I can to complete the project.
  2. I also wanted to get a better understanding of GIT, a source code management system. The last Arduino project I worked on was a test chamber that could control temperature and humidity. I interfaced that with an industrial Touchscreen that I had on hand using Modbus protocol. I have since lost the source code of the project. I did not want to have that happen again. The unit is still working flawlessly, but if I want to make a change, I’ll have to rewrite the whole project again.
  3. I want to be able to add profiles to the controller so I can set it run at temperatures for beef, pork, lamb, ect, as well as timed profiles so I can make yogurt. EG run x number of minutes at y temperature, and then x number of minutes at a different temperature.


I had on hand, an Arduino Uno, bread board, a SainSmart relay board, salvaged pc speaker, a crockpot, electrical outlet, electrical plug and the resister for the one wire sensor.

I had to buy a waterproof one wire temperature sensor, a SainSmart LCD Shield that had built in buttons.

Total cost is estimated at about $60, excluding the crock pot.



I started out slowly adding the parts I wanted to use one by one. I started with the temperature sensor and the example code that can be found with the Dallas library.

I then added the speaker, and used the example for playing melodies. I had to add the Pitch.h file to the project to make that work.

Adding the relay is simple enough, but with my setup, setting the relay pin to low would actually energize the relay coil. So I made a quick define to have RELAY_ON = 0, and RELAY_OFF = 1. This made the code cleaner to read and easier to understand. The relay sends power to the outlet when energized.

The LCD was the easiest part to integrate since it simply plugged into the Uno. But it took some work to find the code needed to set it up.

All of this is plugged into a bread board for the initial setup. This will be finalized later in a project box that I will likely design and print.


The first item to complete was setting up GIT on Windows 7 machine. It took a little reading online but it wasn’t too hard. I will not go into the process here as it can be found online.

Finding examples to build from:

I found the project for the Adafruit Kit which is intended to work with the Adafruit LCD shield and prototyping shield. I like the overall process but it would not work with the LCD shield I had.

Due to the lack of documentation of the SainSmart LCD I had to find examples of interfacing with the unit. I will have a link to the information I found to use this device.


The yogurt bot project I found in Make magazine had a good outline for making a dedicated yogurt fermentation machine. But I want more for this project.



The one-wire sensor is easy enough to use, but the library’s have to work with the newer 1.0+ of the Arduino compiler. So if you have any trouble with the sensor double check that library’s are up to date.

PID control library is used in the Adafruit project, and I want to have a pretty good temperature control setup so I am using that as well as the PID autotune code.

Speaker, as mentioned above, can play melodies, or simple tones. I am using a tone from the example for now, but I plan on changing that later.

Bringing it all together:

I like to use EditPad Pro for the coding of the sketch, and then use the Arduino IDE to compile and upload to the board. The same process can be accomplished with Notepad++. I have used Visual Micro in Visual studio before, but really didn’t care for it. The next time I have a project I think might use Atmel studio. But for now, EditPad Pro it is.



With all the pieces collected, I now have to combine them in some sort of organized mess to make a program. Setup a few defines, include a few library’s, declare a few variables and we are almost done. OK not quite done but it’s a good start.

The basic program flow will work like this:

Setup the sensor, make sure it doesn’t error out. Wait for user input to begin.

User input will decide if a profile will be run, or if the cooker will be at a set temperature. The user can also make changes to the PID tuning, and other settings.


As you can see the project is still in the development phase. It is working with the user defined setpoint. The PID still needs a little tuning to prevent overshoot, but it holds a constant temperature after it settles down from the initial temperature overshoot. I still have to add support for the profiles, additional melodies, and some serial logging. I will be modifying the Uno to prevent it from resetting when serial connection is established. I had serial debugging in the sketch but it actually caused more problems by using up too much memory and bogging down the serial buffer. I’ll slowly add it back in if needed. Of course I still have to package the whole unit up in a nice tidy box. I’ll design that later.


I am standing on the shoulders of giants. Well not really, but I did pull a lot of information from various sources to get the project to this point.

Arduino Modbus connection to a C-more HMI

January 4, 2013

Using an Arduino to collect information from an array of sensors is an economical alternative to using a PLC when the data collection is not critical. In this post I will explain the basics of connecting the hardware of an Arduino to a C-More touch panel from Automation direct. I will then show a basic setting to allow MODBUS communication to work between the two devices.

Hardware you will need:

C-more touch screen:

C-more Comm cable:

Arduino, in this case I used a Duemilanove:

RS232 to TTL converter:

Parts to make a rj12 to db9 connection. I actually used a serial cable cut in half and spliced into a RJ45 jack. You may want to consider a part like this:

Software you will need:

C-more programming software:

The Arduino IDE, I used version 1.01. At the time of writing this 1.03 is available.

The MODBUS library that I got to work with the C-more.

*note this library does not work with Arduino IDE prior to the 1.00 release.

Setting up the hardware.

Create the connector to convert the db9 connection to the RJ12 connection.

DB9 connections required are pin 2, 3,and 5. Pin 7 and 8 will not be used.

To make the RJ45 jack as I did connect make these connections.

DB9 — RJ45

Pin 2 – B4

Pin 3 – B5

Pin 5 – B2

When plugging in the RJ12 to the RJ45, be sure to center the plug in the jack.

###Edit adding Photo to show the intermediary cable.

DB9 to RJ45 hacked cable. Ideally should be DB9 to RJ12.
DB9 to RJ45 hacked cable. Ideally should be DB9 to RJ12.
Here the EA-2CBL RJ12 plug is plugged into the center of the RJ45 jack.

Here the EA-2CBL RJ12 plug is plugged into the center of the RJ45 jack.

( of course you can create your own DB9 to DB15 cable instead )


DB9 |–| DB15

Pin 2 – Pin 3

Pin 3 – Pin 2

Pin 5 – Pin 5

Connecting the Arduino with the RS232 to TTL DTE board

Place jumpers on the RTS and CTS connections at the top of the board. clip_image004

Then make these following connections:

Arduino |—| DTE

5V – VCC

Gnd – GND

Digital pin 0 – RX (Use a jumper wire or place a switch in the middle of this connection.)

Digital pin 1 – TX

Do not connect the RTS or CTS pins from the board to anything.

Configure the Software.

For the Arduino:

Place the MOBUS library into the Arduino IDE library. See this for more information on how to do that:

You can also copy the MODBUSslave example into the example folder.

Launch the Arduino IDE.

Open the MODBUSslave example. ( from the example menu or by navigating to it in the MODBUS library folder.

Now connect to your board. Remove the jumper to the RX pin. ( or turn off the switch if you used one) This will allow the computer to communicate with the Arduino. If you forget to do this, the DTE board will interfere with the upload of the sketch.

Upload the Example to the board.

Once complete, reconnect RX to D0.

C-more setup.

In the C-more software, Start a new project for the panel you have.

Go to Setup -> Panel Manager

On the com port, select the DEV001. Now would be a good time to rename this to ARDUINO.clip_image006

Set PLC Protocol to Modicon Modbus RTU

Select direct connection

Set PLC SLAVE number to 1.

Baud Rate 9600

Parity None

Stop bit 1

Control RTS No

Require CTS No

Select RS 485 No

Byte Order High Byte, Low Byte

Word Order Low Word, High Word

Character Order in register Char1, Char2

Registers per Message 32

Coils per message 64

Register Write Function Code 06

Coil Write Function Code 05

Time out 30

Poll time 3

Click ok.

Let’s place a Numeric Display on the screen,

In the Data Display tag open the tag database to create a new tag.

Click on Add


Select ARDUINO for the device name, Give the tag a name like ReadOnlyRandom.

Set it to Unsigned INT 16

Select memory type 3

Enter an address of 1

Click ADD, Select the new tag Click OK. (notice that the PLC address is shown as 30001)

Click OK again to assign the tag to the display.

Save and send the project to the C-more.

Test it!

Connect the C-more to the Arduino using the com cable.

You should see LEDs on the DTE board flicker and a random number updating on the C-more screen. Congratulations, you have gotten past the biggest hurdle to getting a C-more to talk to an Arduino.

If you do not see this, check that you have RX and Digital pin 0 connected. Also try swapping the RX and TX connections.

Writing to an Arduino

Ok so now you can read from an Arduino, but how about writing to it.

Continuing with the example, let’s add a Numeric Entry in the same fashion as we did with the Numeric Display.

But this time when you add the new tag, Name it WriteableNumber with a memory type of 4 and an address of 9.


Save and transfer the project to the screen.

You should now see a 9 in the new entry.

Change the 9 to a different number. Now you have written to the Arduino.

To make use the register in the Arduino, update the example to use regBank.get(40009).

So in this post I covered how to setup the hardware to between a C-more touch screen HMI, and an Arduino. I also showed how to load the MODBUS library and example onto the Arduino. Lastly I showed how to configure the settings on the C-more to make use of the MODBUS RTU protocol in conjunction with the supported features of the Arduino.

The MODBUS library I used is not the only one available on the web, but it is the first one I got to work with a C-more.

Remember, when you are uploading to the Arduino, you must remove the RX connection.

In the next post, I will share a derived library that takes advantage of SoftSerial. This will allow You to connect the DTE board to Pins 2 and 3 instead of 0 and 1. There by allowing you to upload to the Arduino while remaining connected to the C-more.

Lastly I will share some methods to make it easy to read and write discrete bits using whole registers, instead of coils.

Please let me know what you think of this post. I welcome questions and feedback.